Ardex - Polyurethane Coving Systems

Self Smoothing Epoxy Floor Systems - Wall Renders - Polyurethane Coving Systems - Product Selector

ARDEX R 15 P Low Viscosity Repair System & Renovation Coating For Application to Polyurethane Floors

High performance, polyurethane resin coating, supplied as three components in pre-measured packs for ease of on site mixing and use. The cured system forms a tough, easily cleaned, pigmented layer on existing polyurethane toppings.

Properties

The values shown are typical results obtained in the laboratory at 20°C. Actual performance values obtained on site may vary from those quoted.

Physical Properties: @ 20°C Approximately
Working Life: 10 mins
Light Traffic: 24 hrs
Full Traffic: 48 hrs
Full Chemical Cure: 7 days
Bond Strength:>1.5N/mm²

Coverage: A 3.3kg pack of ARDEX R 15 P will yield 2.2 litres which will cover between 10 and 20m² dependent on the texture, applied thickness and substrate condition.

Standard Colours:
Green, Grey, Orange, Red, Cream, Yellow

ARDEX R 10 P Polyurethane Coving & Wall Render

High performance, polyurethane resin wall and coving system, supplied as four components in pre-measured packs for ease of on site mixing and use. The cured system forms a tough, easily cleaned, pigmented layer from a feather edge up to 12mm thick.

Properties

The values shown are typical of results obtained in the laboratory at 20ºC. Actual performance values obtained on site may vary from those quoted.

Physical Properties: @ 20ºC Approximately
Pot Life: 10 mins
Light Use: 24 hrs
Full Use: 48 hrs
Full Chemical Cure: 7 days
Bond Strength: > 1.5 N/mm² Compressive Strength: 45 N/mm² Flexural Strength: 11 N/mm² Tensile Strength: 5 N/mm²

Coverage: A 13.9kg pack of ARDEX R10P Polyurethane Coving and Wall Render will cover approximately 1.4m² at 5mm thick.

Note: These figures are theoretical, due to wastage and the variety and nature of substrates practical coverage figures may be reduced.

Standard Colours:
Green, Grey, Orange, Red, Cream, Yellow

ARDEX R 25 E Self-smoothing Epoxy Floor System

High performance, epoxy resin flooring system, supplied as three components in a pre-measured pack for ease of on site mixing and use. The cured resin forms a pigmented, smooth, tough 2 - 4mm layer, which can be easily cleaned.

Properties

The values shown are typical of results obtained in the laboratory at 20ºC. Actual performance values obtained on site may vary from those quoted.

Physical Properties: @ 20ºC Approximately
Pot Life: 30 mins
Initial Hardness: 24 hrs
Full Cure: 7 days
Compressive Strength: 70 N/mm²
Flexural Strength: 31 N/mm²
Tensile Strength: 23 N/mm²
Coverage: A 15.9kg unit will cover approximately 4.7m² @ 2mm thick.

Note: These figures are theoretical, due to wastage and the variety and nature of substrates practical coverage figures may be reduced.

Standard Colours:
Mid Green, Mid Grey, Light Grey, Mid Blue, Tile Red

ARDEX R 30 E Water-based Epoxy Coating

Water-based epoxy coating to provide an easily cleaned surface, resistant to many common oils and liquids with excellent adhesion to concrete and cement/sand screeds.

Properties

The values shown are typical of results obtained in the laboratory at 20ºC. Actual performance values obtained on site may vary from those quoted.

Physical Properties: @ 20ºC Approximately
Pot Life: 45 mins
Time Between Coats: 8 - 24hrs
Walkability: 24 hrs
Full Cure: 7 days
Dry Film Thickness: 2 coats 100 microns (approx.)
Coverage: A 6kg unit will cover 30 - 45m² per pack per 100 micron coat.

Note: These figures are theoretical, due to wastage and the variety and nature of substrates practical coverage figures may be reduced.

Standard Colours:
Mid Green, Mid Grey, Light Grey, Mid Blue, Tile Red